Home > Blades > Rodding Blades
We found 8 results matching your criteria.
Alpha Duster
Slayer
Filter:
Page of 1
DRB04
4" DUSTER RODDING BLADE
Our Price: $69.00

This 4" by 1/4" thick blade is designed for cutting slots in the back of granite slabs to rod it for extra strength.
DRB05
5" DUSTER RODDING BLADE
Our Price: $80.00

This 5" by 5/16" thick blade is designed for cutting slots in the back of granite slabs to rod it for extra strength.
ALHT03A
Alpha Hot-Rod Blades 3"
Our Price: $94.96

Alpha Hot-Rod Blades
Cutting Channels for Support Rods
For Use With Granite

Max RPM: 14,500
Arbor: 7/8", 20mm
Recommended For: 1/8" Rod
Thickness: 4.2mm


Alpha® developed a revolutionary way to improve the efficiency of fabricators.
For years, slab fabricators have employed labor-intensive procedures for creating
channels in the underside of countertops to accommodate stainless steel reinforcing
rods at sink and cooktop cutouts. Alpha® recognized the opportunity for improvement
and developed the Alpha® Hot-Rod. With this blade attached to the Alpha® AWS-110
or AWS-125 Wet Stone Cutter, a fabricator can accomplish the task in one easy pass.
The Hot-Rod for Granite blades were created with diamond grits and matrix best suited
for all categories of granite, including hard red granites, to assure a long cutting life.
With a 3” diameter, the blade allows for easy use and better leverage when cutting 1/4”
deep channels, by allowing for better positioning of the stone cutter’s handle. This blade
is now available in three thicknesses: 1/4” for standard rods, 1/8” for thinner rods and
3/8” for threaded rods. The Hot-Rod for Marble applies the same technology but is designed
for softer stones such as marble. This blade is available in 1/4” for standard and 1/8” for
thinner rods.For efficient creation of channels for reinforcing rods, attach this unique blade t
o our AWS-110 or AWS-125 for a smooth, dust-free operation. Used in this manner, productivity
will increase significantly. Although Alpha® recommends wet cutting, these blades may be
used wet or dry.
ALHQ03A
Alpha Hot-Rod Blades 3"
Our Price: $94.96

Alpha Hot-Rod Blades
Cutting Channels for Support Rods
For Use With Granite

Max RPM: 14,500
Arbor:
7/8", 20mm
Recommended For:
3/16" Rod
Thickness:
5.5mm


Alpha® developed a revolutionary way to improve the efficiency of fabricators.
For years, slab fabricators have employed labor-intensive procedures for creating
channels in the underside of countertops to accommodate stainless steel reinforcing
rods at sink and cooktop cutouts. Alpha® recognized the opportunity for improvement
and developed the Alpha® Hot-Rod. With this blade attached to the Alpha® AWS-110
or AWS-125 Wet Stone Cutter, a fabricator can accomplish the task in one easy pass.
The Hot-Rod for Granite blades were created with diamond grits and matrix best suited
for all categories of granite, including hard red granites, to assure a long cutting life.
With a 3” diameter, the blade allows for easy use and better leverage when cutting 1/4”
deep channels, by allowing for better positioning of the stone cutter’s handle. This blade
is now available in three thicknesses: 1/4” for standard rods, 1/8” for thinner rods and
3/8” for threaded rods. The Hot-Rod for Marble applies the same technology but is designed
for softer stones such as marble. This blade is available in 1/4” for standard and 1/8” for
thinner rods.For efficient creation of channels for reinforcing rods, attach this unique blade t
o our AWS-110 or AWS-125 for a smooth, dust-free operation. Used in this manner, productivity
will increase significantly. Although Alpha® recommends wet cutting, these blades may be
used wet or dry.
ALHR03A
Alpha Hot-Rod Blades 3"
Our Price: $94.96

Alpha Hot-Rod Blades
Cutting Channels for Support Rods
For Use With Granite

Max RPM: 14,500
Arbor:
7/8", 20mm
Recommended For:
1/4" Rod
Thickness:
7mm


Alpha® developed a revolutionary way to improve the efficiency of fabricators.
For years, slab fabricators have employed labor-intensive procedures for creating
channels in the underside of countertops to accommodate stainless steel reinforcing
rods at sink and cooktop cutouts. Alpha® recognized the opportunity for improvement
and developed the Alpha® Hot-Rod. With this blade attached to the Alpha® AWS-110
or AWS-125 Wet Stone Cutter, a fabricator can accomplish the task in one easy pass.
The Hot-Rod for Granite blades were created with diamond grits and matrix best suited
for all categories of granite, including hard red granites, to assure a long cutting life.
With a 3” diameter, the blade allows for easy use and better leverage when cutting 1/4”
deep channels, by allowing for better positioning of the stone cutter’s handle. This blade
is now available in three thicknesses: 1/4” for standard rods, 1/8” for thinner rods and
3/8” for threaded rods. The Hot-Rod for Marble applies the same technology but is designed
for softer stones such as marble. This blade is available in 1/4” for standard and 1/8” for
thinner rods.For efficient creation of channels for reinforcing rods, attach this unique blade t
o our AWS-110 or AWS-125 for a smooth, dust-free operation. Used in this manner, productivity
will increase significantly. Although Alpha® recommends wet cutting, these blades may be
used wet or dry.
ALHS03A
Alpha Hot-Rod Blades 3"
Our Price: $94.96

Alpha Hot-Rod Blades
Cutting Channels for Support Rods
For Use With Marble

Max RPM: 14,500
Arbor:
7/8", 20mm
Recommended For:
1/8" Rod
Thickness:
4.6mm


Alpha® developed a revolutionary way to improve the efficiency of fabricators.
For years, slab fabricators have employed labor-intensive procedures for creating
channels in the underside of countertops to accommodate stainless steel reinforcing
rods at sink and cooktop cutouts. Alpha® recognized the opportunity for improvement
and developed the Alpha® Hot-Rod. With this blade attached to the Alpha® AWS-110
or AWS-125 Wet Stone Cutter, a fabricator can accomplish the task in one easy pass.
The Hot-Rod for Granite blades were created with diamond grits and matrix best suited
for all categories of granite, including hard red granites, to assure a long cutting life.
With a 3” diameter, the blade allows for easy use and better leverage when cutting 1/4”
deep channels, by allowing for better positioning of the stone cutter’s handle. This blade
is now available in three thicknesses: 1/4” for standard rods, 1/8” for thinner rods and
3/8” for threaded rods. The Hot-Rod for Marble applies the same technology but is designed
for softer stones such as marble. This blade is available in 1/4” for standard and 1/8” for
thinner rods.For efficient creation of channels for reinforcing rods, attach this unique blade t
o our AWS-110 or AWS-125 for a smooth, dust-free operation. Used in this manner, productivity
will increase significantly. Although Alpha® recommends wet cutting, these blades may be
used wet or dry.
ALHM03A
Alpha Hot-Rod Blades 3"
Our Price: $94.96

Alpha Hot-Rod Blades
Cutting Channels for Support Rods
For Use With Marble

Max RPM: 14,500
Arbor:
7/8", 20mm
Recommended For:
1/4" Rod
Thickness:
6.5mm


Alpha® developed a revolutionary way to improve the efficiency of fabricators.
For years, slab fabricators have employed labor-intensive procedures for creating
channels in the underside of countertops to accommodate stainless steel reinforcing
rods at sink and cooktop cutouts. Alpha® recognized the opportunity for improvement
and developed the Alpha® Hot-Rod. With this blade attached to the Alpha® AWS-110
or AWS-125 Wet Stone Cutter, a fabricator can accomplish the task in one easy pass.
The Hot-Rod for Granite blades were created with diamond grits and matrix best suited
for all categories of granite, including hard red granites, to assure a long cutting life.
With a 3” diameter, the blade allows for easy use and better leverage when cutting 1/4”
deep channels, by allowing for better positioning of the stone cutter’s handle. This blade
is now available in three thicknesses: 1/4” for standard rods, 1/8” for thinner rods and
3/8” for threaded rods. The Hot-Rod for Marble applies the same technology but is designed
for softer stones such as marble. This blade is available in 1/4” for standard and 1/8” for
thinner rods.For efficient creation of channels for reinforcing rods, attach this unique blade t
o our AWS-110 or AWS-125 for a smooth, dust-free operation. Used in this manner, productivity
will increase significantly. Although Alpha® recommends wet cutting, these blades may be
used wet or dry.
ALHW03A
Alpha Hot-Rod Blades 3"
Our Price: $108.30

Alpha Hot-Rod Blades
Cutting Channels for Support Rods
For Use With Granite

Max RPM: 14,500
Arbor:
7/8"
Recommended For:
3/8" Threaded Rod
Thickness:
11.5mm


Alpha® developed a revolutionary way to improve the efficiency of fabricators.
For years, slab fabricators have employed labor-intensive procedures for creating
channels in the underside of countertops to accommodate stainless steel reinforcing
rods at sink and cooktop cutouts. Alpha® recognized the opportunity for improvement
and developed the Alpha® Hot-Rod. With this blade attached to the Alpha® AWS-110
or AWS-125 Wet Stone Cutter, a fabricator can accomplish the task in one easy pass.
The Hot-Rod for Granite blades were created with diamond grits and matrix best suited
for all categories of granite, including hard red granites, to assure a long cutting life.
With a 3” diameter, the blade allows for easy use and better leverage when cutting 1/4”
deep channels, by allowing for better positioning of the stone cutter’s handle. This blade
is now available in three thicknesses: 1/4” for standard rods, 1/8” for thinner rods and
3/8” for threaded rods. The Hot-Rod for Marble applies the same technology but is designed
for softer stones such as marble. This blade is available in 1/4” for standard and 1/8” for
thinner rods.For efficient creation of channels for reinforcing rods, attach this unique blade t
o our AWS-110 or AWS-125 for a smooth, dust-free operation. Used in this manner, productivity
will increase significantly. Although Alpha® recommends wet cutting, these blades may be
used wet or dry.